APRS Track Direct

My position About ☰

reset

ED6ZAB-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object ED6ZAB-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1732309310	13.65 Volt	20 Pkt	20 Pkt	20 Pcnt
1732308710	13.65 Volt	20 Pkt	20 Pkt	20 Pcnt
1732308110	13.65 Volt	30 Pkt	20 Pkt	21 Pcnt
1732307510	13.65 Volt	30 Pkt	20 Pkt	21 Pcnt
1732306910	13.65 Volt	40 Pkt	30 Pkt	26 Pcnt
1732306310	13.65 Volt	50 Pkt	30 Pkt	27 Pcnt
1732305710	13.73 Volt	50 Pkt	30 Pkt	27 Pcnt
1732305110	13.73 Volt	50 Pkt	30 Pkt	25 Pcnt
1732304510	13.73 Volt	50 Pkt	30 Pkt	26 Pcnt
1732303910	13.73 Volt	50 Pkt	30 Pkt	26 Pcnt
1732303310	13.73 Volt	40 Pkt	30 Pkt	23 Pcnt
1732302710	13.73 Volt	30 Pkt	20 Pkt	20 Pcnt
1732302110	13.73 Volt	30 Pkt	20 Pkt	20 Pcnt
1732301510	13.73 Volt	30 Pkt	20 Pkt	22 Pcnt
1732300910	13.73 Volt	40 Pkt	30 Pkt	25 Pcnt
1732300311	13.73 Volt	50 Pkt	30 Pkt	28 Pcnt
1732299710	13.73 Volt	60 Pkt	40 Pkt	35 Pcnt
1732299110	13.65 Volt	70 Pkt	40 Pkt	33 Pcnt
1732298510	13.73 Volt	70 Pkt	40 Pkt	32 Pcnt
1732297910	13.73 Volt	60 Pkt	40 Pkt	30 Pcnt
1732297310	13.65 Volt	60 Pkt	30 Pkt	28 Pcnt
1732296710	13.65 Volt	50 Pkt	30 Pkt	26 Pcnt
1732296111	13.73 Volt	40 Pkt	20 Pkt	22 Pcnt
1732295510	13.73 Volt	40 Pkt	20 Pkt	22 Pcnt
1732294910	13.73 Volt	40 Pkt	30 Pkt	26 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)