APRS Track Direct

My position About ☰

reset

N0OWT-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object N0OWT-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Battery*	PC Board Temp*	-*
1758199655	13.7 V	24 F	0 On=255 Off=0
1758197856	13.4 V	25 F	0 On=255 Off=0
1758196955	13.6 V	25 F	0 On=255 Off=0
1758196057	13.6 V	25 F	0 On=255 Off=0
1758195154	13.7 V	23 F	0 On=255 Off=0
1758194255	13.6 V	23 F	0 On=255 Off=0
1758193357	13.5 V	24 F	0 On=255 Off=0
1758192456	13.6 V	25 F	0 On=255 Off=0
1758191554	13.6 V	24 F	0 On=255 Off=0
1758190656	13.6 V	23 F	0 On=255 Off=0
1758189756	13.7 V	24 F	0 On=255 Off=0
1758188855	13.7 V	23 F	0 On=255 Off=0
1758187954	13.8 V	24 F	0 On=255 Off=0
1758187055	13.8 V	25 F	0 On=255 Off=0
1758185255	13.9 V	24 F	0 On=255 Off=0
1758184354	13.8 V	23 F	0 On=255 Off=0
1758183455	13.9 V	24 F	0 On=255 Off=0
1758182554	13.8 V	24 F	0 On=255 Off=0
1758181656	13.8 V	24 F	0 On=255 Off=0
1758180755	13.8 V	22 F	0 On=255 Off=0
1758179855	13.9 V	23 F	0 On=255 Off=0
1758177155	13.9 V	24 F	0 On=255 Off=0
1758176257	13.8 V	24 F	0 On=255 Off=0
1758175355	13.7 V	22 F	0 On=255 Off=0
1758174455	13.7 V	23 F	0 On=255 Off=0

*Used Equation Coefficients:

Battery: 0, 0.1, 0

PC Board Temp: 0, 1, 0

-: 0, 1, 0

-: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)