APRS Track Direct

My position About ☰

reset

EA3BNF-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object EA3BNF-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Radiacion*	VOC*
1774152470	0.17 uSv/h	154.45 iaq
1774151834	0.2 uSv/h	153.66 iaq
1774151197	0.19 uSv/h	155.24 iaq
1774150561	0.21 uSv/h	149.77 iaq
1774149924	0.2 uSv/h	149.77 iaq
1774149287	0.18 uSv/h	148.23 iaq
1774148651	0.19 uSv/h	147.46 iaq
1774148014	0.21 uSv/h	140.63 iaq
1774147377	0.17 uSv/h	140.63 iaq
1774146741	0.18 uSv/h	141.38 iaq
1774146104	0.18 uSv/h	139.88 iaq
1774145467	0.24 uSv/h	144.4 iaq
1774144831	0.22 uSv/h	143.64 iaq
1774144194	0.21 uSv/h	142.88 iaq
1774143557	0.2 uSv/h	139.13 iaq
1774142921	0.23 uSv/h	138.38 iaq
1774142284	0.19 uSv/h	135.42 iaq
1774141647	0.21 uSv/h	133.96 iaq
1774141011	0.18 uSv/h	133.96 iaq
1774140374	0.17 uSv/h	132.5 iaq
1774139737	0.18 uSv/h	131.77 iaq
1774139101	0.16 uSv/h	130.32 iaq
1774138464	0.17 uSv/h	131.04 iaq
1774137827	0.21 uSv/h	133.23 iaq
1774137190	0.23 uSv/h	127.45 iaq

*Used Equation Coefficients:

Radiacion: 0, 0.01, 0

VOC: 0.001, 0, 0

PM2.5: 0, 1, 0

PM10: 0, 1, 0

CO2: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)