APRS Track Direct

My position About ☰

reset

KNAPPA Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KNAPPA. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Battery*	Watts*	Array-East*	Array-West*	Charging*
1836274534	13.25 Volts	0 W	0.05 V	0.05 V	0 A
1836274414	13.26 Volts	0 W	0.05 V	0.07 V	0 A
1836273904	13.25 Volts	0 W	0.05 V	0.11 V	0 A
1762311683	13.32 Volts	0 W	0.05 V	0.17 V	0 A
1762311053	13.32 Volts	0 W	0.06 V	0.16 V	0 A
1762310423	13.33 Volts	0 W	0.05 V	0.05 V	0 A
1762309793	13.34 Volts	0 W	0.05 V	0.03 V	0 A
1762309163	13.35 Volts	0 W	0.03 V	0.12 V	0 A
1762308533	13.36 Volts	0 W	0.06 V	0.09 V	0 A
1762307903	13.39 Volts	0 W	0.03 V	0.08 V	0 A
1762307273	13.49 Volts	0 W	0.07 V	0.18 V	0 A
1762306643	13.5 Volts	0 W	0.16 V	0.3 V	0 A
1762306013	13.46 Volts	0 W	0.56 V	1.03 V	0 A
1762305383	13.39 Volts	0 W	3.61 V	7.89 V	0 A
1762304753	13.25 Volts	1 W	14.14 V	14 V	0.04 A
1762304123	13.24 Volts	0 W	14.26 V	14.03 V	0.01 A
1762303493	13.25 Volts	0 W	14.25 V	14.13 V	0.01 A
1762302863	13.27 Volts	0 W	14.31 V	14.06 V	0.02 A
1762302233	13.26 Volts	1 W	14.31 V	14.17 V	0.08 A
1762301603	13.26 Volts	2 W	14.36 V	14.17 V	0.18 A
1762300973	13.28 Volts	3 W	14.37 V	14.23 V	0.2 A
1762300343	13.28 Volts	3 W	14.38 V	14.17 V	0.19 A
1762299713	13.26 Volts	3 W	14.39 V	14.19 V	0.26 A
1762299083	13.29 Volts	5 W	14.44 V	14.27 V	0.41 A
1762298453	13.3 Volts	6 W	14.46 V	14.28 V	0.45 A

*Used Equation Coefficients:

Battery: 0, 1, 0

Watts: 0, 1, 0

Array-East: 0, 1, 0

Array-West: 0, 1, 0

Charging: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)