APRS Track Direct

My position About ☰

reset

KA6PRW-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KA6PRW-9. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Battery*	Temp*
1774471143	13.27 Volts	31.99 Deg.C
1774471110	13.39 Volts	31.99 Deg.C
1774471102	13.36 Volts	31.99 Deg.C
1774471094	13.42 Volts	31.5 Deg.C
1774471080	13.45 Volts	31.5 Deg.C
1774471051	13.45 Volts	31.5 Deg.C
1774470937	13.36 Volts	31.5 Deg.C
1774470829	13.3 Volts	31.01 Deg.C
1774470742	13.48 Volts	31.01 Deg.C
1774470736	13.48 Volts	31.01 Deg.C
1774470639	13.51 Volts	30.52 Deg.C
1774470547	13.45 Volts	30.52 Deg.C
1774470452	13.39 Volts	30.52 Deg.C
1774470116	13.3 Volts	29.54 Deg.C
1774470020	13.21 Volts	29.05 Deg.C
1774469764	13.24 Volts	27.1 Deg.C
1774469734	13.21 Volts	26.61 Deg.C
1774469646	13.27 Volts	25.63 Deg.C
1774469591	13.39 Volts	25.14 Deg.C
1774465146	13.42 Volts	23.67 Deg.C
1774465146	13.45 Volts	23.67 Deg.C
1774465146	13.36 Volts	24.65 Deg.C
1774464731	13.33 Volts	27.59 Deg.C
1774464538	13.33 Volts	26.12 Deg.C
1774464513	13.33 Volts	25.63 Deg.C

*Used Equation Coefficients:

Battery: 0, 0.0293, 0

Temp: 0, 0.489, -273.15

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)