APRS Track Direct

My position About ☰

reset

S55UJE-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object S55UJE-11. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Uacu*	Iacu*	Temp*	Rx1h*
1758206357	13.61 Volt	6.27 A	63.5 C	150 Pkt
1758206356	13.61 Volt	6.27 A	63.5 C	150 Pkt
1758206057	13.61 Volt	5.88 A	63.5 C	140 Pkt
1758206056	13.61 Volt	5.88 A	63.5 C	140 Pkt
1758205757	13.61 Volt	6.66 A	63.5 C	140 Pkt
1758205756	13.61 Volt	6.66 A	63.5 C	140 Pkt
1758205456	13.61 Volt	6.27 A	63.5 C	140 Pkt
1758205456	13.61 Volt	6.27 A	63.5 C	140 Pkt
1758205156	13.61 Volt	6.66 A	63.5 C	140 Pkt
1758205155	13.61 Volt	6.66 A	63.5 C	140 Pkt
1758204856	13.61 Volt	6.66 A	63.5 C	140 Pkt
1758204855	13.61 Volt	6.66 A	63.5 C	140 Pkt
1758204555	13.61 Volt	6.66 A	63.5 C	150 Pkt
1758204555	13.61 Volt	6.66 A	63.5 C	150 Pkt
1758204255	13.61 Volt	6.66 A	63.5 C	150 Pkt
1758204254	13.61 Volt	6.66 A	63.5 C	150 Pkt
1758203955	13.61 Volt	6.66 A	63.5 C	140 Pkt
1758203954	13.61 Volt	6.66 A	63.5 C	140 Pkt
1758203655	13.61 Volt	7.05 A	63.5 C	140 Pkt
1758203654	13.61 Volt	7.05 A	63.5 C	140 Pkt
1758203354	13.61 Volt	6.66 A	63.5 C	140 Pkt
1758203354	13.61 Volt	6.66 A	63.5 C	140 Pkt
1758203057	13.61 Volt	7.44 A	63.5 C	130 Pkt
1758203053	13.61 Volt	7.44 A	63.5 C	130 Pkt
1758202754	13.61 Volt	7.83 A	63.5 C	130 Pkt

*Used Equation Coefficients:

Uacu: 0, 0.100819, 0

Iacu: 0, 0.3917, -49.7457

Temp: 0, 0.5, -64

Rx1h: 0, 10, 0

WIND: 0, 0.1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)