APRS Track Direct

My position About ☰

reset

YD6SVI-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YD6SVI-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1774537135	24 Pkt	-86 dBm	0.12 V
1774536465	29 Pkt	-87 dBm	0.12 V
1774535795	27 Pkt	-86 dBm	0.12 V
1774535125	24 Pkt	-87 dBm	0.14 V
1774534455	24 Pkt	-87 dBm	0.14 V
1774533785	26 Pkt	-87 dBm	0.12 V
1774533115	26 Pkt	-87 dBm	0.12 V
1774532445	26 Pkt	-87 dBm	0.12 V
1774531775	28 Pkt	-87 dBm	0.12 V
1774531105	25 Pkt	-87 dBm	0.12 V
1774530435	23 Pkt	-86 dBm	0.12 V
1774529765	25 Pkt	-87 dBm	0.12 V
1774529095	64 Pkt	-87 dBm	0.12 V
1774528425	25 Pkt	-87 dBm	0.14 V
1774527755	27 Pkt	-87 dBm	0.12 V
1774527085	24 Pkt	-87 dBm	0.12 V
1774526415	23 Pkt	-87 dBm	0.14 V
1774525745	27 Pkt	-86 dBm	0.12 V
1774525075	29 Pkt	-88 dBm	0.12 V
1774524405	22 Pkt	-87 dBm	0.14 V
1774523735	26 Pkt	-87 dBm	0.12 V
1774523065	27 Pkt	-86 dBm	0.14 V
1774522395	24 Pkt	-86 dBm	0.12 V
1774521725	29 Pkt	-86 dBm	0.12 V
1774521055	27 Pkt	-88 dBm	0.14 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)