APRS Track Direct

My position About ☰

reset

DB0HEI-12 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DB0HEI-12. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Temp.in*	Hum*	Temp.out*
1782513879	2 C deg	20.1 %	42.7 C deg
1782512063	2 C deg	19.1 %	42.9 C deg
1782510248	2 C deg	18.5 %	43.2 C deg
1782508432	2 C deg	18.8 %	43 C deg
1782506616	2 C deg	18.5 %	43.8 C deg
1782504800	2 C deg	18.9 %	43.7 C deg
1782502985	2 C deg	18.9 %	44.3 C deg
1782501169	2 C deg	19.2 %	43.4 C deg
1782499353	2 C deg	19.1 %	43.6 C deg
1782497538	2 C deg	20 %	43.8 C deg
1782495721	2 C deg	20.8 %	43.3 C deg
1782493905	2 C deg	20.2 %	43.6 C deg
1782492091	2 C deg	19.5 %	44.1 C deg
1782490274	2 C deg	19.6 %	43.4 C deg
1782488458	2 C deg	19.7 %	42.6 C deg
1782486643	2 C deg	19.2 %	42.9 C deg
1782484827	2 C deg	19 %	42.9 C deg
1782483010	2 C deg	18.9 %	42.4 C deg
1782481195	2 C deg	18.2 %	42.9 C deg
1782479379	2 C deg	18.7 %	42.4 C deg
1782477563	2 C deg	20.2 %	41.6 C deg
1782475748	2 C deg	21.4 %	41.6 C deg
1782473932	2 C deg	22.4 %	41.5 C deg
1782472116	2 C deg	23.7 %	41.4 C deg
1782470301	2 C deg	24.6 %	41.3 C deg

*Used Equation Coefficients:

Press: 0, 1, 0

Temp.in: 0, 1, 0

Hum: 0, 1, 0

QNH: 0, 1, 0

Temp.out: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)