APRS Track Direct

My position About ☰

reset

IW9CSJ-15 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object IW9CSJ-15. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vcc*	Temp DC-DC*	Temp P.S.*
1786749369	12.46 Volt	35.6 C	46.3 C
1786749250	12.41 Volt	35.6 C	46.3 C
1786749129	12.39 Volt	35.6 C	46.3 C
1786749010	12.46 Volt	35.6 C	46.3 C
1786748890	12.46 Volt	35.6 C	46.3 C
1786748769	12.46 Volt	35.7 C	46.3 C
1786748650	12.46 Volt	35.7 C	46.3 C
1786748530	12.39 Volt	35.7 C	46.3 C
1786748409	12.39 Volt	35.7 C	46.4 C
1786748290	12.41 Volt	35.7 C	46.4 C
1786748169	12.46 Volt	35.8 C	46.4 C
1786748050	12.43 Volt	35.8 C	46.4 C
1786747930	12.43 Volt	35.8 C	46.4 C
1786747810	12.43 Volt	35.8 C	46.5 C
1786747690	12.43 Volt	35.8 C	46.5 C
1786747569	12.46 Volt	35.8 C	46.5 C
1786747450	12.41 Volt	35.8 C	46.5 C
1786747329	12.43 Volt	35.8 C	46.5 C
1786747210	12.39 Volt	35.8 C	46.5 C
1786747090	12.46 Volt	35.8 C	46.5 C
1786746970	12.46 Volt	35.8 C	46.5 C
1786746850	12.46 Volt	35.8 C	46.5 C
1786746729	12.41 Volt	35.8 C	46.5 C
1786746610	12.46 Volt	35.8 C	46.5 C
1786746490	12.43 Volt	35.8 C	46.5 C

*Used Equation Coefficients:

Solare: 0, 1, 0

Batteria: 0, 1, 0

Vcc: 0, 1, 0

Temp DC-DC: 0, 1, 0

Temp P.S.: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)