APRS Track Direct

My position About ☰

reset

BV4HW-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BV4HW-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*	DiGi*
1778033439	32.1 C	16 p	44 p	83 p	77 p
1778032238	32.9 C	29 p	49 p	81 p	75 p
1778027439	25.4 C	14 p	18 p	18 p	17 p
1778026239	24.8 C	4 p	4 p	4 p	3 p
1778025038	18.8 C	5 p	13 p	304 p	289 p
1777974551	31 C	7 p	16 p	303 p	288 p
1777973351	31.4 C	4 p	35 p	296 p	281 p
1777972150	31.6 C	5 p	50 p	292 p	278 p
1777970953	30.2 C	26 p	86 p	289 p	275 p
1777969751	30.6 C	21 p	67 p	263 p	249 p
1777968551	30.5 C	38 p	75 p	243 p	229 p
1777966150	31.1 C	29 p	64 p	196 p	188 p
1777964958	31 C	12 p	43 p	168 p	164 p
1777963751	31.6 C	25 p	37 p	157 p	153 p
1777961350	31 C	5 p	39 p	125 p	122 p
1777960150	31.5 C	12 p	35 p	120 p	117 p
1777958950	29.7 C	24 p	26 p	110 p	107 p
1777957750	28.3 C	1 p	18 p	86 p	84 p
1777956550	30.5 C	1 p	40 p	85 p	83 p
1777955351	32.2 C	16 p	44 p	84 p	82 p
1777954151	30.9 C	34 p	57 p	81 p	79 p
1777951750	30.3 C	20 p	44 p	44 p	43 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)