APRS Track Direct

My position About ☰

reset

XE2J-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object XE2J-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Vin*	Eff1h*	Temp*
1782526729	11.18 Volt	100 Pcnt	22.5 C
1782525829	11.78 Volt	100 Pcnt	23.5 C
1782524929	12.15 Volt	100 Pcnt	24.5 C
1782524029	12.3 Volt	100 Pcnt	25.5 C
1782523129	12.45 Volt	100 Pcnt	27 C
1782522229	12.6 Volt	100 Pcnt	28.5 C
1782521329	12.68 Volt	100 Pcnt	30 C
1782520429	12.75 Volt	100 Pcnt	31.5 C
1782519529	12.75 Volt	100 Pcnt	33 C
1782518630	12.75 Volt	100 Pcnt	34.5 C
1782517730	12.75 Volt	100 Pcnt	35 C
1782516830	12.75 Volt	100 Pcnt	37 C
1782515929	12.75 Volt	100 Pcnt	36 C
1782515030	12.75 Volt	100 Pcnt	36.5 C
1782514130	12.75 Volt	100 Pcnt	36.5 C
1782513230	12.83 Volt	100 Pcnt	36 C
1782512330	12.83 Volt	100 Pcnt	35.5 C
1782511430	12.9 Volt	100 Pcnt	35 C
1782510530	12.83 Volt	100 Pcnt	34.5 C
1782509630	12.9 Volt	100 Pcnt	34.5 C
1782508730	12.9 Volt	100 Pcnt	33.5 C
1782507830	12.68 Volt	100 Pcnt	33.5 C
1782506930	12.9 Volt	100 Pcnt	33 C
1782506030	12.68 Volt	100 Pcnt	32 C
1782505130	12.9 Volt	100 Pcnt	32.5 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)