APRS Track Direct

My position About ☰

reset

IQ3GO-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object IQ3GO-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx10m*	Rx1h*	Eff1h*	Vin*
1754206308	1 Pkt	20 Pkt	62 Pcnt	12.15 Volt
1754206008	1 Pkt	20 Pkt	61 Pcnt	12.15 Volt
1754205708	2 Pkt	20 Pkt	65 Pcnt	12.15 Volt
1754205408	1 Pkt	20 Pkt	64 Pcnt	12.15 Volt
1754205108	10 Pkt	20 Pkt	64 Pcnt	12.15 Volt
1754204808	16 Pkt	20 Pkt	64 Pcnt	12.15 Volt
1754204508	10 Pkt	10 Pkt	58 Pcnt	12.15 Volt
1754204208	4 Pkt	0 Pkt	60 Pcnt	12.15 Volt
1754203908	1 Pkt	0 Pkt	60 Pcnt	12.15 Volt
1754203608	0 Pkt	0 Pkt	71 Pcnt	12.15 Volt
1754203308	0 Pkt	0 Pkt	83 Pcnt	12.15 Volt
1754203008	0 Pkt	0 Pkt	83 Pcnt	12.15 Volt
1754202708	2 Pkt	0 Pkt	100 Pcnt	12.15 Volt
1754202408	1 Pkt	0 Pkt	100 Pcnt	12.15 Volt
1754202108	1 Pkt	0 Pkt	83 Pcnt	12.15 Volt
1754201808	1 Pkt	0 Pkt	83 Pcnt	12.15 Volt
1754201508	2 Pkt	0 Pkt	85 Pcnt	12.15 Volt
1754201208	0 Pkt	0 Pkt	80 Pcnt	12.15 Volt
1754200908	0 Pkt	0 Pkt	80 Pcnt	12.15 Volt
1754200608	0 Pkt	0 Pkt	80 Pcnt	12.15 Volt
1754200308	0 Pkt	0 Pkt	80 Pcnt	12.15 Volt
1754200008	0 Pkt	0 Pkt	80 Pcnt	12.15 Volt
1754199708	1 Pkt	0 Pkt	80 Pcnt	12.15 Volt
1754199408	1 Pkt	0 Pkt	80 Pcnt	12.15 Volt
1754199108	1 Pkt	0 Pkt	80 Pcnt	12.15 Volt

*Used Equation Coefficients:

Rx10m: 0, 1, 0

Rx1h: 0, 10, 0

Dg10m: 0, 1, 0

Eff1h: 0, 1, 0

Vin: 0, 0.075, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)