APRS Track Direct

My position About ☰

reset

TA8DRU-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object TA8DRU-11. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	TxTraffic*	RSSI*	Voltage*
1774783013	0 Pkt	-77 dBm	10.42 V
1774782637	4 Pkt	-78 dBm	9.99 V
1774781833	0 Pkt	-77 dBm	8.18 V
1774781028	0 Pkt	-78 dBm	8.31 V
1774780657	3 Pkt	-77 dBm	6.89 V
1774779853	5 Pkt	-78 dBm	7.55 V
1774779048	0 Pkt	-78 dBm	8.14 V
1774778855	4 Pkt	-77 dBm	9.7 V
1774778050	0 Pkt	-77 dBm	9.97 V
1774777861	2 Pkt	-77 dBm	10.62 V
1774777057	0 Pkt	-76 dBm	13 V
1774776881	39 Pkt	-77 dBm	12.63 V
1774776077	1 Pkt	-75 dBm	11.94 V
1774775895	2 Pkt	-77 dBm	11.63 V
1774775091	0 Pkt	-77 dBm	9.95 V
1774774899	2 Pkt	-76 dBm	10.19 V
1774774095	0 Pkt	-79 dBm	6.44 V
1774773909	2 Pkt	-78 dBm	6.09 V
1774773104	0 Pkt	-80 dBm	8.55 V
1774772930	2 Pkt	-80 dBm	8.2 V
1774772125	1 Pkt	-80 dBm	8.24 V
1774771746	4 Pkt	-81 dBm	10.44 V
1774770138	1 Pkt	-79 dBm	11.36 V
1774769964	1 Pkt	-81 dBm	10.5 V
1774769160	0 Pkt	-82 dBm	9.99 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)