APRS Track Direct

My position About ☰

reset

E24TVS-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object E24TVS-11. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	TxTraffic*	RSSI*	Voltage*
1786731063	1 Pkt	-52 dBm	19.4 V
1786729841	0 Pkt	-59 dBm	15.69 V
1786728619	0 Pkt	-59 dBm	1 V
1786727397	1 Pkt	-57 dBm	8.88 V
1786726175	0 Pkt	-58 dBm	14.77 V
1786724954	0 Pkt	-57 dBm	21 V
1786723732	2 Pkt	-60 dBm	11.67 V
1786722509	0 Pkt	-57 dBm	21 V
1786721415	0 Pkt	-57 dBm	19.26 V
1786720160	0 Pkt	-57 dBm	0 V
1786718952	0 Pkt	-62 dBm	0 V
1786717643	0 Pkt	-56 dBm	20.77 V
1786716486	0 Pkt	-60 dBm	2.21 V
1786710915	0 Pkt	-51 dBm	0 V
1786709918	0 Pkt	-57 dBm	0.78 V
1786708681	0 Pkt	-59 dBm	0.64 V
1786708119	0 Pkt	-56 dBm	0.43 V
1786705565	2 Pkt	-56 dBm	8.65 V
1786704368	0 Pkt	-57 dBm	5.74 V
1786704002	0 Pkt	-58 dBm	14.87 V
1786702780	0 Pkt	-57 dBm	0.49 V
1786701558	0 Pkt	-58 dBm	14.23 V
1786700336	0 Pkt	-57 dBm	8.29 V
1786699114	15 Pkt	-57 dBm	1.09 V
1786697892	0 Pkt	-57 dBm	11.34 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)