APRS Track Direct

My position About ☰

reset

KI5FUN-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KI5FUN-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	RFIn*	RFiGate*	Temp*
1762287524	333 Pkts	328 Pkts	9 C
1762283924	334 Pkts	326 Pkts	9 C
1762280324	362 Pkts	353 Pkts	7 C
1762276724	461 Pkts	456 Pkts	9 C
1762273124	404 Pkts	399 Pkts	9 C
1762269524	443 Pkts	433 Pkts	8 C
1762265924	372 Pkts	364 Pkts	8 C
1762262323	370 Pkts	365 Pkts	8 C
1762258724	348 Pkts	344 Pkts	8 C
1762255124	365 Pkts	358 Pkts	8 C
1762251524	337 Pkts	330 Pkts	8 C
1762247924	354 Pkts	348 Pkts	8 C
1762244324	392 Pkts	386 Pkts	9 C
1762240724	386 Pkts	377 Pkts	8 C
1762237124	387 Pkts	381 Pkts	8 C
1762233524	488 Pkts	482 Pkts	8 C
1762229924	464 Pkts	457 Pkts	8 C
1762226324	484 Pkts	476 Pkts	9 C
1762222724	485 Pkts	479 Pkts	8 C
1762219124	438 Pkts	433 Pkts	9 C
1762215525	465 Pkts	460 Pkts	9 C
1762211924	457 Pkts	451 Pkts	9 C
1762208324	461 Pkts	457 Pkts	9 C
1762204724	360 Pkts	354 Pkts	9 C

*Used Equation Coefficients:

RFIn: 0, 1, 0

RFiGate: 0, 1, 0

DigiRpt: 0, 1, 0

Temp: 0, 1, 0

InetiGate: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)