APRS Track Direct

My position About ☰

reset

ED4ZAI-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object ED4ZAI-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	Vin*	Rx1h*	Dg1h*	Eff1h*	Temp*
1768410417	12.6 Volt	210 Pkt	90 Pkt	88 Pcnt	10 C
1768408617	13.35 Volt	270 Pkt	120 Pkt	89 Pcnt	10 C
1768406817	13.58 Volt	300 Pkt	140 Pkt	88 Pcnt	10 C
1768405017	14.1 Volt	300 Pkt	150 Pkt	86 Pcnt	10 C
1768403217	14.1 Volt	190 Pkt	110 Pkt	83 Pcnt	10 C
1768401417	14.48 Volt	130 Pkt	70 Pkt	86 Pcnt	9 C
1768399617	12.45 Volt	100 Pkt	50 Pkt	84 Pcnt	9 C
1768397817	12.45 Volt	80 Pkt	40 Pkt	80 Pcnt	9 C
1768396017	12.98 Volt	80 Pkt	40 Pkt	75 Pcnt	9 C
1768394217	14.4 Volt	80 Pkt	40 Pkt	72 Pcnt	8.5 C
1768392417	13.2 Volt	90 Pkt	40 Pkt	72 Pcnt	8.5 C
1768390617	12.9 Volt	80 Pkt	30 Pkt	74 Pcnt	8.5 C
1768388817	14.4 Volt	80 Pkt	40 Pkt	71 Pcnt	8 C
1768329518	11.48 Volt	100 Pkt	50 Pkt	74 Pcnt	9 C
1768327718	11.85 Volt	70 Pkt	30 Pkt	63 Pcnt	9 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)