APRS Track Direct

My position About ☰

reset

E25RZY-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object E25RZY-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	TxTraffic*	RSSI*	Voltage*
1786749569	0 Pkt	-52 dBm	14.54 V
1786748646	0 Pkt	-56 dBm	14.56 V
1786747724	0 Pkt	-50 dBm	14.54 V
1786746803	0 Pkt	-57 dBm	14.48 V
1786745881	0 Pkt	-54 dBm	14.52 V
1786744959	0 Pkt	-67 dBm	14.48 V
1786723825	0 Pkt	-62 dBm	14.44 V
1786722903	2 Pkt	-57 dBm	14.54 V
1786721981	0 Pkt	-56 dBm	14.46 V
1786721059	0 Pkt	-58 dBm	14.54 V
1786720137	0 Pkt	-60 dBm	14.48 V
1786719215	0 Pkt	-59 dBm	14.56 V
1786718293	0 Pkt	-58 dBm	14.54 V
1786717371	0 Pkt	-58 dBm	14.54 V
1786716449	0 Pkt	-55 dBm	14.46 V
1786715527	0 Pkt	-55 dBm	14.48 V
1786714605	0 Pkt	-58 dBm	14.54 V
1786713683	0 Pkt	-54 dBm	14.52 V
1786712761	0 Pkt	-54 dBm	14.52 V
1786711839	0 Pkt	-57 dBm	14.42 V
1786710917	0 Pkt	-57 dBm	14.52 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)