APRS Track Direct

My position About ☰

reset

HP1LDF-12 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HP1LDF-12. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	RxTraffic*	RSSI*	Voltage*
1836274500	6 Pkt	-69 dBm	13.97 V
1762315333	0 Pkt	-68 dBm	13.97 V
1762314109	0 Pkt	-67 dBm	13.97 V
1762312884	1 Pkt	-66 dBm	13.97 V
1762311659	0 Pkt	-66 dBm	13.97 V
1762310435	0 Pkt	-65 dBm	13.97 V
1762309210	0 Pkt	-65 dBm	13.97 V
1762307986	0 Pkt	-66 dBm	13.97 V
1762306762	0 Pkt	-66 dBm	13.97 V
1762305537	0 Pkt	-66 dBm	13.97 V
1762304312	0 Pkt	-66 dBm	13.95 V
1762303088	0 Pkt	-67 dBm	13.97 V
1762301863	0 Pkt	-66 dBm	13.95 V
1762300639	0 Pkt	-65 dBm	13.97 V
1762299414	0 Pkt	-66 dBm	13.95 V
1762298190	0 Pkt	-69 dBm	13.97 V
1762296965	0 Pkt	-67 dBm	13.97 V
1762295741	0 Pkt	-67 dBm	13.95 V
1762294516	0 Pkt	-67 dBm	13.95 V
1762293292	0 Pkt	-68 dBm	13.97 V
1762292067	0 Pkt	-67 dBm	13.97 V
1762290842	0 Pkt	-67 dBm	13.97 V
1762289618	0 Pkt	-66 dBm	13.97 V
1762288393	0 Pkt	-67 dBm	13.97 V
1762287169	0 Pkt	-68 dBm	13.97 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)