APRS Track Direct

My position About ☰

reset

E23JWE-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object E23JWE-2. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	TxTraffic*	RSSI*	Voltage*
1792070445	0 Pkt	-28 dBm	6.64 V
1792068782	0 Pkt	-33 dBm	6.6 V
1792066956	0 Pkt	-27 dBm	6.64 V
1792065130	0 Pkt	-27 dBm	7.03 V
1792063305	0 Pkt	-28 dBm	6.6 V
1792061479	1 Pkt	-27 dBm	6.79 V
1792059631	0 Pkt	-28 dBm	6.42 V
1792057806	1 Pkt	-28 dBm	6.67 V
1792055981	0 Pkt	-31 dBm	6.97 V
1792054155	1 Pkt	-28 dBm	6.99 V
1792052330	1 Pkt	-27 dBm	6.91 V
1792050504	1 Pkt	-28 dBm	6.93 V
1792048679	3 Pkt	-28 dBm	6.99 V
1792046854	0 Pkt	-27 dBm	6.77 V
1792045029	2 Pkt	-28 dBm	6.95 V
1792043203	2 Pkt	-29 dBm	6.54 V
1792041378	0 Pkt	-26 dBm	7.03 V
1792039552	0 Pkt	-28 dBm	7.05 V
1792037727	0 Pkt	-28 dBm	7.14 V
1792035901	0 Pkt	-29 dBm	7.16 V
1792034076	0 Pkt	-28 dBm	7.16 V
1792032250	1 Pkt	-28 dBm	6.83 V
1792030425	0 Pkt	-31 dBm	6.71 V
1792028599	0 Pkt	-28 dBm	6.99 V
1792026774	0 Pkt	-28 dBm	7.03 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)