APRS Track Direct

My position About ☰

reset

K5KP-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object K5KP-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	RFIn*	RFiGate*	DigiRpt*	Temp*
1770145270	6 Pkts	2 Pkts	2 Pkts	32 C
1770141670	5 Pkts	0 Pkts	0 Pkts	31 C
1770138070	6 Pkts	2 Pkts	0 Pkts	32 C
1770134470	9 Pkts	5 Pkts	3 Pkts	31 C
1770130870	30 Pkts	25 Pkts	6 Pkts	32 C
1770127270	46 Pkts	41 Pkts	11 Pkts	32 C
1770123670	15 Pkts	10 Pkts	4 Pkts	32 C
1770120070	13 Pkts	10 Pkts	3 Pkts	33 C
1770116470	17 Pkts	11 Pkts	3 Pkts	32 C
1770112870	31 Pkts	26 Pkts	9 Pkts	32 C
1770109269	26 Pkts	22 Pkts	5 Pkts	32 C
1770105669	33 Pkts	28 Pkts	14 Pkts	32 C
1770102070	25 Pkts	21 Pkts	11 Pkts	32 C
1770098469	26 Pkts	21 Pkts	7 Pkts	32 C
1770094869	25 Pkts	19 Pkts	9 Pkts	32 C
1770091270	25 Pkts	18 Pkts	7 Pkts	33 C
1770087670	27 Pkts	21 Pkts	12 Pkts	33 C
1770084070	77 Pkts	73 Pkts	23 Pkts	34 C
1770080470	96 Pkts	90 Pkts	11 Pkts	33 C
1770076870	27 Pkts	21 Pkts	11 Pkts	34 C
1770073270	27 Pkts	19 Pkts	11 Pkts	33 C
1770069670	10 Pkts	5 Pkts	3 Pkts	32 C
1770066075	16 Pkts	13 Pkts	9 Pkts	31 C
1770062470	9 Pkts	3 Pkts	3 Pkts	31 C

*Used Equation Coefficients:

RFIn: 0, 1, 0

RFiGate: 0, 1, 0

DigiRpt: 0, 1, 0

Temp: 0, 1, 0

InetiGate: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)