APRS Track Direct

My position About ☰

reset

TA4RE-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object TA4RE-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	RxTraffic*	RSSI*	Voltage*
1782556116	3 Pkt	-67 dBm	11.14 V
1782555193	2 Pkt	-68 dBm	11.14 V
1782554271	1 Pkt	-68 dBm	11.14 V
1782553349	3 Pkt	-67 dBm	11.14 V
1782552427	1 Pkt	-68 dBm	11.14 V
1782551505	1 Pkt	-68 dBm	11.16 V
1782550587	1 Pkt	-68 dBm	11.14 V
1782549660	1 Pkt	-68 dBm	11.14 V
1782548738	2 Pkt	-67 dBm	11.14 V
1782547816	1 Pkt	-68 dBm	11.14 V
1782546894	1 Pkt	-68 dBm	11.14 V
1782545972	12 Pkt	-68 dBm	11.14 V
1782545049	6 Pkt	-68 dBm	11.14 V
1782544126	9 Pkt	-68 dBm	11.14 V
1782543203	2 Pkt	-68 dBm	11.14 V
1782542281	3 Pkt	-68 dBm	11.14 V
1782541405	2 Pkt	-68 dBm	11.14 V
1782540483	0 Pkt	-69 dBm	11.14 V
1782539605	3 Pkt	-68 dBm	11.14 V
1782538682	0 Pkt	-68 dBm	11.14 V
1782537898	1 Pkt	-68 dBm	11.14 V
1782536976	2 Pkt	-68 dBm	11.14 V
1782536054	1 Pkt	-66 dBm	11.14 V
1782535132	1 Pkt	-65 dBm	11.14 V
1782534210	1 Pkt	-66 dBm	11.14 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)