APRS Track Direct

My position About ☰

reset

LU2BFM-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LU2BFM-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	RxTraffic*	RxDrop*	RSSI*	Voltage*
1770434659	29 Pkt	2 Pkt	31 dBm	14.6 V
1770423783	19 Pkt	1 Pkt	31 dBm	14.6 V
1770416534	62 Pkt	12 Pkt	31 dBm	14.56 V
1770412908	24 Pkt	11 Pkt	31 dBm	14.58 V
1770409284	12 Pkt	10 Pkt	31 dBm	14.56 V
1770405663	21 Pkt	10 Pkt	31 dBm	14.56 V
1770402038	25 Pkt	10 Pkt	31 dBm	14.56 V
1770394792	28 Pkt	15 Pkt	31 dBm	14.56 V
1770387545	37 Pkt	19 Pkt	31 dBm	14.58 V
1770383919	7 Pkt	0 Pkt	31 dBm	14.58 V
1770380258	55 Pkt	12 Pkt	31 dBm	14.6 V
1770376632	73 Pkt	5 Pkt	31 dBm	14.6 V
1770373006	58 Pkt	2 Pkt	31 dBm	14.6 V
1770369380	52 Pkt	2 Pkt	31 dBm	14.6 V
1770365753	48 Pkt	1 Pkt	31 dBm	14.6 V
1770362126	56 Pkt	4 Pkt	31 dBm	14.6 V
1770354874	62 Pkt	1 Pkt	31 dBm	14.6 V
1770351248	39 Pkt	0 Pkt	31 dBm	14.6 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)