APRS Track Direct

☰

reset

K4KSC-12 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object K4KSC-12. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	Value1*	Value2*	Value3*	Value5*
1792147639	53.2 V	-0.7 A	76 %	17 W
1792147037	53.2 V	-0.8 A	76 %	17 W
1792146440	53.2 V	-0.9 A	76 %	17 W
1792145840	53.2 V	-0.7 A	76 %	17 W
1792145240	53.2 V	-0.7 A	77 %	17 W
1792144640	53.2 V	-0.8 A	77 %	17 W
1792144040	53.2 V	-0.9 A	77 %	17 W
1792142840	53.2 V	-0.7 A	78 %	16 W
1792142240	53.2 V	-0.7 A	78 %	17 W
1792141640	53.2 V	-1 A	78 %	17 W
1792141041	53.2 V	-0.9 A	78 %	18 W
1792140440	53.2 V	-0.6 A	79 %	16 W
1792139837	53.2 V	-0.8 A	79 %	16 W
1792139240	53.2 V	-0.7 A	79 %	18 W
1792138641	53.2 V	-0.9 A	79 %	16 W
1792138041	53.2 V	-0.7 A	80 %	17 W
1792137441	53.2 V	-0.7 A	80 %	17 W
1792136840	53.2 V	-0.8 A	80 %	17 W
1792136240	53.2 V	-0.9 A	80 %	16 W
1792135041	53.2 V	-0.7 A	81 %	17 W
1792134440	53.2 V	-0.9 A	81 %	16 W
1792133841	53.2 V	-0.8 A	81 %	17 W
1792133240	53.2 V	-0.7 A	82 %	17 W
1792132638	53.2 V	-0.8 A	82 %	17 W
1792132040	53.2 V	-0.9 A	82 %	17 W

*Used Equation Coefficients:

Value1: 0, 1, 0

Value2: 0, 1, 0

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Maintained by UW0WU-1, based on APRS Track Direct