APRS Track Direct

My position About ☰

reset

W4VA-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object W4VA-13. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	T1*	Rx10m*	Eff1h*
1758200458	24.5 C	211 Pkt	63 Pcnt
1758200158	24.5 C	213 Pkt	62 Pcnt
1758199858	24.5 C	206 Pkt	62 Pcnt
1758199558	24 C	155 Pkt	61 Pcnt
1758199258	24 C	143 Pkt	62 Pcnt
1758198958	24 C	129 Pkt	61 Pcnt
1758198658	24 C	143 Pkt	61 Pcnt
1758198358	24 C	158 Pkt	62 Pcnt
1758198058	24 C	164 Pkt	61 Pcnt
1758197758	24.5 C	141 Pkt	62 Pcnt
1758197458	24.5 C	157 Pkt	62 Pcnt
1758197158	25 C	159 Pkt	62 Pcnt
1758196858	24 C	166 Pkt	62 Pcnt
1758196558	24 C	161 Pkt	62 Pcnt
1758196258	24.5 C	167 Pkt	63 Pcnt
1758195958	24.5 C	167 Pkt	63 Pcnt
1758195658	24.5 C	164 Pkt	62 Pcnt
1758195358	24.5 C	163 Pkt	63 Pcnt
1758195058	24 C	166 Pkt	63 Pcnt
1758194758	24 C	152 Pkt	63 Pcnt
1758194458	24 C	137 Pkt	64 Pcnt
1758194158	24 C	161 Pkt	65 Pcnt
1758193858	24.5 C	161 Pkt	65 Pcnt
1758193558	25 C	160 Pkt	65 Pcnt
1758193258	24.5 C	144 Pkt	66 Pcnt

*Used Equation Coefficients:

T1: 0, 0.5, -64

Rx10m: 0, 1, 0

Dg10m: 0, 1, 0

Eff1h: 0, 1, 0

DgR1h: 0, 0.001, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)