APRS Track Direct

My position About ☰

reset

W3TM-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object W3TM-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	RFIn*	RFiGate*	DigiRpt*	Temp*
1790638670	76 Pkts	70 Pkts	9 Pkts	4 C
1790635070	57 Pkts	55 Pkts	8 Pkts	4 C
1790631470	69 Pkts	65 Pkts	12 Pkts	4 C
1790627870	69 Pkts	65 Pkts	14 Pkts	4 C
1790624270	71 Pkts	68 Pkts	15 Pkts	4 C
1790620670	95 Pkts	91 Pkts	12 Pkts	4 C
1790617070	76 Pkts	72 Pkts	18 Pkts	4 C
1790613470	64 Pkts	60 Pkts	12 Pkts	4 C
1790609871	53 Pkts	52 Pkts	13 Pkts	4 C
1790606270	56 Pkts	54 Pkts	8 Pkts	4 C
1790602670	75 Pkts	74 Pkts	12 Pkts	4 C
1790599070	94 Pkts	89 Pkts	13 Pkts	4 C
1790595470	92 Pkts	88 Pkts	27 Pkts	4 C
1790591870	76 Pkts	70 Pkts	10 Pkts	4 C
1790588270	77 Pkts	75 Pkts	9 Pkts	4 C
1790584670	76 Pkts	75 Pkts	14 Pkts	3 C
1790581070	75 Pkts	72 Pkts	14 Pkts	4 C
1790577470	77 Pkts	74 Pkts	10 Pkts	4 C
1790573870	71 Pkts	69 Pkts	12 Pkts	4 C
1790570270	63 Pkts	59 Pkts	13 Pkts	4 C
1790566670	60 Pkts	59 Pkts	12 Pkts	4 C
1790563070	70 Pkts	68 Pkts	8 Pkts	4 C
1790559470	58 Pkts	55 Pkts	12 Pkts	4 C
1790555870	56 Pkts	55 Pkts	13 Pkts	4 C

*Used Equation Coefficients:

RFIn: 0, 1, 0

RFiGate: 0, 1, 0

DigiRpt: 0, 1, 0

Temp: 0, 1, 0

InetiGate: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)