APRS Track Direct

My position About ☰

reset

YM6KV-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YM6KV-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	TxTraffic*	RSSI*	Voltage*
1774129388	17 Pkt	-63 dBm	11.98 V
1774127549	15 Pkt	-65 dBm	11.98 V
1774125709	14 Pkt	-66 dBm	12 V
1774123867	13 Pkt	-63 dBm	12 V
1774122031	15 Pkt	-66 dBm	11.98 V
1774120194	23 Pkt	-64 dBm	11.98 V
1774118346	23 Pkt	-67 dBm	11.98 V
1774116496	16 Pkt	-70 dBm	11.98 V
1774114655	17 Pkt	-69 dBm	11.98 V
1774112815	20 Pkt	-70 dBm	11.98 V
1774110969	53 Pkt	-75 dBm	11.98 V
1774109098	40 Pkt	-66 dBm	11.98 V
1774107235	23 Pkt	-72 dBm	11.98 V
1774105388	41 Pkt	-59 dBm	12 V
1774103523	16 Pkt	-63 dBm	11.98 V
1774101683	23 Pkt	-61 dBm	11.98 V
1774099991	18 Pkt	-58 dBm	11.98 V
1774098150	16 Pkt	-58 dBm	11.98 V
1774096309	0 Pkt	-56 dBm	11.98 V
1774096106	16 Pkt	-58 dBm	12 V
1774094264	17 Pkt	-56 dBm	12 V
1774092423	16 Pkt	-58 dBm	11.98 V
1774090585	14 Pkt	-64 dBm	12 V
1774088747	16 Pkt	-61 dBm	11.98 V
1774086905	15 Pkt	-62 dBm	11.98 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)