APRS Track Direct

My position About ☰

reset

TC3EC Telemetry

This is the latest recevied telemetry packets stored in our database for station/object TC3EC. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	TxTraffic*	RSSI*	Voltage*
1758231870	1 Pkt	-71 dBm	11.48 V
1758231321	105 Pkt	-70 dBm	11.46 V
1758229489	107 Pkt	-73 dBm	11.48 V
1758227656	112 Pkt	-70 dBm	11.48 V
1758225824	114 Pkt	-71 dBm	11.46 V
1758223991	107 Pkt	-70 dBm	11.5 V
1758222157	101 Pkt	-69 dBm	11.46 V
1758220325	108 Pkt	-71 dBm	11.46 V
1758218493	111 Pkt	-70 dBm	11.46 V
1758216661	96 Pkt	-70 dBm	11.44 V
1758214829	111 Pkt	-72 dBm	11.48 V
1758213002	96 Pkt	-70 dBm	11.46 V
1758211170	88 Pkt	-72 dBm	11.48 V
1758209336	92 Pkt	-71 dBm	11.46 V
1758207504	121 Pkt	-69 dBm	11.46 V
1758205670	146 Pkt	-70 dBm	11.48 V
1758203832	114 Pkt	-73 dBm	11.46 V
1758201999	96 Pkt	-72 dBm	11.46 V
1758200166	98 Pkt	-71 dBm	11.46 V
1758198334	93 Pkt	-72 dBm	11.46 V
1758196347	6 Pkt	-71 dBm	11.46 V
1758195296	106 Pkt	-72 dBm	11.48 V
1758193464	120 Pkt	-70 dBm	11.46 V
1758191630	104 Pkt	-68 dBm	11.46 V
1758189797	106 Pkt	-66 dBm	11.48 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)