APRS Track Direct

My position About ☰

reset

E27ASY-4 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object E27ASY-4. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1790648425	1 Pkt	-70 dBm	12.74 V
1790648103	1 Pkt	-70 dBm	20.1 V
1790647781	0 Pkt	-71 dBm	20.2 V
1790647459	0 Pkt	-71 dBm	19.44 V
1790647137	0 Pkt	-70 dBm	12.8 V
1790646815	0 Pkt	-70 dBm	12.74 V
1790646493	1 Pkt	-70 dBm	20.28 V
1790646171	0 Pkt	-70 dBm	20.26 V
1790645849	0 Pkt	-70 dBm	12.76 V
1790645527	0 Pkt	-70 dBm	13.99 V
1790645205	2 Pkt	-70 dBm	13.92 V
1790644883	0 Pkt	-70 dBm	13.84 V
1790644561	0 Pkt	-68 dBm	13.8 V
1790644239	2 Pkt	-69 dBm	13.74 V
1790643917	0 Pkt	-69 dBm	13.66 V
1790643595	0 Pkt	-70 dBm	13.64 V
1790643273	0 Pkt	-70 dBm	13.41 V
1790642951	6 Pkt	-70 dBm	13.41 V
1790642629	0 Pkt	-70 dBm	13.33 V
1790642307	0 Pkt	-69 dBm	13.25 V
1790641985	0 Pkt	-70 dBm	13.13 V
1790630249	0 Pkt	-72 dBm	12.12 V
1790629927	0 Pkt	-73 dBm	12.22 V
1790629605	0 Pkt	-72 dBm	12.3 V
1790629283	0 Pkt	-72 dBm	12.33 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)