APRS Track Direct

My position About ☰

reset

HS9UAC-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HS9UAC-2. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	TxTraffic*	RSSI*	Voltage*
1790652660	0 Pkt	-36 dBm	5.48 V
1790648968	4 Pkt	-37 dBm	5.17 V
1790645341	10 Pkt	-40 dBm	5.48 V
1790641713	13 Pkt	-35 dBm	5.48 V
1790638085	9 Pkt	-38 dBm	5.19 V
1790634457	3 Pkt	-39 dBm	5.48 V
1790630830	0 Pkt	-44 dBm	5.48 V
1790627202	3 Pkt	-38 dBm	5.48 V
1790623575	4 Pkt	-41 dBm	5.48 V
1790619948	1 Pkt	-37 dBm	5.48 V
1790616320	3 Pkt	-41 dBm	5.48 V
1790612693	7 Pkt	-46 dBm	5.17 V
1790609065	6 Pkt	-40 dBm	5.48 V
1790605441	6 Pkt	-42 dBm	5.17 V
1790601810	0 Pkt	-36 dBm	5.48 V
1790598183	0 Pkt	-38 dBm	5.48 V
1790594555	3 Pkt	-38 dBm	5.48 V
1790590928	1 Pkt	-37 dBm	5.13 V
1790587300	0 Pkt	-41 dBm	5.48 V
1790583673	3 Pkt	-42 dBm	5.13 V
1790580045	3 Pkt	-41 dBm	5.48 V
1790576418	2 Pkt	-37 dBm	5.48 V
1790572791	1 Pkt	-38 dBm	5.48 V
1790569163	3 Pkt	-37 dBm	5.48 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)