APRS Track Direct

My position About ☰

reset

HS0GWL-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HS0GWL-2. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	TxTraffic*	RSSI*	Voltage*
1836274388	0 Pkt	-69 dBm	13.04 V
1762343515	0 Pkt	-65 dBm	12.49 V
1762342293	0 Pkt	-66 dBm	12.51 V
1762341071	0 Pkt	-65 dBm	12.59 V
1762339849	0 Pkt	-66 dBm	12.63 V
1762338627	0 Pkt	-66 dBm	12.63 V
1762337405	1 Pkt	-66 dBm	12.63 V
1762336183	0 Pkt	-67 dBm	12.67 V
1762334961	0 Pkt	-66 dBm	12.69 V
1762333739	0 Pkt	-65 dBm	12.69 V
1762332517	1 Pkt	-65 dBm	12.69 V
1762331295	1 Pkt	-66 dBm	12.71 V
1762330073	0 Pkt	-66 dBm	12.76 V
1762328850	0 Pkt	-68 dBm	12.74 V
1762327628	0 Pkt	-67 dBm	12.8 V
1762326407	0 Pkt	-67 dBm	12.84 V
1762325185	0 Pkt	-68 dBm	12.9 V
1762323962	0 Pkt	-67 dBm	12.82 V
1762322741	0 Pkt	-67 dBm	13.17 V
1762321518	1 Pkt	-68 dBm	13.62 V
1762320296	1 Pkt	-69 dBm	13.78 V
1762319074	0 Pkt	-68 dBm	13.47 V
1762317852	0 Pkt	-69 dBm	13.64 V
1762316630	0 Pkt	-67 dBm	13.68 V
1762315408	2 Pkt	-69 dBm	13.64 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)