This is the latest recevied telemetry packets stored in our database for station/object OE3XWJ-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | Vin* | Rx1h* | Dg1h* | Eff1h* | Total* |
|---|---|---|---|---|---|
| 1786725362 | 13.27 Volt | 660 Pkt | 270 Pkt | 61 Pcnt | 60 Pcnt |
| 1786718155 | 13.27 Volt | 650 Pkt | 270 Pkt | 65 Pcnt | 60 Pcnt |
| 1786710952 | 13.27 Volt | 730 Pkt | 290 Pkt | 62 Pcnt | 60 Pcnt |
| 1786703742 | 13.27 Volt | 660 Pkt | 350 Pkt | 64 Pcnt | 60 Pcnt |
| 1786696534 | 13.19 Volt | 720 Pkt | 350 Pkt | 59 Pcnt | 60 Pcnt |
| 1786689327 | 13.19 Volt | 780 Pkt | 430 Pkt | 63 Pcnt | 60 Pcnt |
| 1786682122 | 13.27 Volt | 750 Pkt | 330 Pkt | 62 Pcnt | 60 Pcnt |
| 1786674914 | 13.27 Volt | 700 Pkt | 350 Pkt | 63 Pcnt | 60 Pcnt |
| 1786667707 | 13.27 Volt | 620 Pkt | 300 Pkt | 60 Pcnt | 60 Pcnt |
| 1786660500 | 13.27 Volt | 530 Pkt | 240 Pkt | 58 Pcnt | 60 Pcnt |
| 1786653296 | 13.27 Volt | 520 Pkt | 220 Pkt | 59 Pcnt | 60 Pcnt |
| 1786646087 | 13.27 Volt | 620 Pkt | 250 Pkt | 63 Pcnt | 60 Pcnt |
*Used Equation Coefficients:
Vin: 0, 0.079, 0
Rx1h: 0, 10, 0
Dg1h: 0, 10, 0
Eff1h: 0, 1, 0
Total: 0, 1, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)