APRS Track Direct

My position About ☰

reset

HS5XHC-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HS5XHC-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1786747125	0 Pkt	-19 dBm	12.45 V
1786746501	0 Pkt	-20 dBm	12.45 V
1786745877	0 Pkt	-20 dBm	12.47 V
1786745253	0 Pkt	-19 dBm	12.45 V
1786744629	0 Pkt	-20 dBm	12.47 V
1786744005	0 Pkt	-19 dBm	12.45 V
1786743381	0 Pkt	-17 dBm	12.45 V
1786742757	0 Pkt	-19 dBm	12.47 V
1786742133	0 Pkt	-20 dBm	12.45 V
1786741510	0 Pkt	-18 dBm	12.47 V
1786740886	1 Pkt	-20 dBm	12.47 V
1786740262	1 Pkt	-19 dBm	12.45 V
1786739638	0 Pkt	-20 dBm	12.45 V
1786739014	0 Pkt	-20 dBm	12.47 V
1786738390	0 Pkt	-19 dBm	12.45 V
1786737766	0 Pkt	-20 dBm	12.45 V
1786737529	0 Pkt	-20 dBm	12.47 V
1786736905	0 Pkt	-21 dBm	12.43 V
1786736281	0 Pkt	-20 dBm	12.47 V
1786735657	0 Pkt	-20 dBm	12.45 V
1786735033	0 Pkt	-20 dBm	12.45 V
1786734410	0 Pkt	-20 dBm	12.45 V
1786733785	0 Pkt	-21 dBm	12.45 V
1786733161	0 Pkt	-20 dBm	12.45 V
1786732538	0 Pkt	-21 dBm	12.45 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)