APRS Track Direct

My position About ☰

reset

PU4RON-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object PU4RON-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	TxTraffic*	RSSI*	Voltage*
1774485777	196 Pkt	-37 dBm	0.08 V
1774484508	201 Pkt	-39 dBm	0.08 V
1774483239	186 Pkt	-38 dBm	0.08 V
1774481970	134 Pkt	-38 dBm	0.08 V
1774480701	153 Pkt	-38 dBm	0.08 V
1774479432	171 Pkt	-38 dBm	0.08 V
1774478164	175 Pkt	-37 dBm	0.08 V
1774476894	176 Pkt	-37 dBm	0.08 V
1774475625	133 Pkt	-37 dBm	0.08 V
1774474356	156 Pkt	-37 dBm	0.08 V
1774473089	167 Pkt	-37 dBm	0.08 V
1774471819	154 Pkt	-39 dBm	0.08 V
1774470551	237 Pkt	-39 dBm	0.08 V
1774469275	204 Pkt	-39 dBm	0.08 V
1774468007	162 Pkt	-38 dBm	0.08 V
1774466739	183 Pkt	-40 dBm	0.08 V
1774465471	200 Pkt	-38 dBm	0.08 V
1774464204	174 Pkt	-39 dBm	0.08 V
1774462936	193 Pkt	-37 dBm	0.08 V
1774461667	198 Pkt	-39 dBm	0.08 V
1774460400	188 Pkt	-38 dBm	0.08 V
1774459133	135 Pkt	-39 dBm	0.08 V
1774457865	153 Pkt	-38 dBm	0.08 V
1774456596	155 Pkt	-39 dBm	0.08 V
1774455328	187 Pkt	-38 dBm	0.08 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)