APRS Track Direct

My position About ☰

reset

HA2EBO-4 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HA2EBO-4. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	Voltage*	BoardTemp*	CPUTemp*	Current*
1766335962	11.87 Volt	23.53 DegC	52.94 DegC	0.8 A
1766334162	11.87 Volt	23.53 DegC	52.94 DegC	0.8 A
1766332362	11.87 Volt	23.53 DegC	53.88 DegC	0.8 A
1766330562	11.87 Volt	23.53 DegC	53.88 DegC	0.8 A
1766328762	11.87 Volt	23.53 DegC	52.94 DegC	0.9 A
1766326962	11.87 Volt	24.47 DegC	53.88 DegC	0.9 A
1766325162	11.87 Volt	23.53 DegC	53.88 DegC	0.8 A
1766323362	11.87 Volt	24.47 DegC	53.88 DegC	0.8 A
1766321562	11.87 Volt	24.47 DegC	53.88 DegC	0.8 A
1766317962	11.87 Volt	24.47 DegC	53.88 DegC	0.9 A
1766316162	11.87 Volt	24.47 DegC	54.82 DegC	0.8 A
1766314362	11.87 Volt	24.47 DegC	55.76 DegC	0.9 A
1766312562	11.87 Volt	24.47 DegC	53.88 DegC	0.8 A
1766310762	11.87 Volt	24.47 DegC	53.88 DegC	0.8 A
1766308962	11.87 Volt	24.47 DegC	53.88 DegC	0.8 A
1766307162	11.87 Volt	24.47 DegC	52.94 DegC	0.8 A
1766303562	11.87 Volt	24.47 DegC	53.88 DegC	0.8 A
1766301964	11.87 Volt	24.47 DegC	56.7 DegC	1 A

*Used Equation Coefficients:

Voltage: 0, 0.0157, 10

BoardTemp: 0, 0.3137, 0

CPUTemp: 0, 0.3137, 20

Current: 0, 0.0118, 0

Unused: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)