APRS Track Direct

My position About ☰

reset

DB0TIT-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DB0TIT-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1786716077	13.9 Volt	430 Pkt	110 Pkt	52 Pcnt
1786712477	13.9 Volt	360 Pkt	100 Pkt	52 Pcnt
1786708878	13.9 Volt	390 Pkt	80 Pkt	52 Pcnt
1786705277	13.9 Volt	330 Pkt	60 Pkt	52 Pcnt
1786701678	13.9 Volt	330 Pkt	50 Pkt	52 Pcnt
1786698077	13.9 Volt	410 Pkt	70 Pkt	52 Pcnt
1786694478	13.9 Volt	370 Pkt	60 Pkt	52 Pcnt
1786690878	13.9 Volt	360 Pkt	70 Pkt	52 Pcnt
1786687278	13.9 Volt	460 Pkt	80 Pkt	52 Pcnt
1786683678	13.9 Volt	340 Pkt	80 Pkt	52 Pcnt
1786680078	13.9 Volt	290 Pkt	80 Pkt	52 Pcnt
1786676478	13.9 Volt	260 Pkt	60 Pkt	52 Pcnt
1786672879	13.9 Volt	220 Pkt	60 Pkt	52 Pcnt
1786669279	13.9 Volt	180 Pkt	60 Pkt	52 Pcnt
1786665679	13.9 Volt	160 Pkt	40 Pkt	52 Pcnt
1786662079	13.9 Volt	140 Pkt	50 Pkt	52 Pcnt
1786658479	13.9 Volt	150 Pkt	50 Pkt	52 Pcnt
1786654880	13.9 Volt	150 Pkt	30 Pkt	52 Pcnt
1786651280	13.9 Volt	200 Pkt	60 Pkt	52 Pcnt
1786647681	13.9 Volt	360 Pkt	80 Pkt	52 Pcnt
1786644080	13.9 Volt	260 Pkt	60 Pkt	52 Pcnt
1786640481	13.9 Volt	250 Pkt	60 Pkt	52 Pcnt
1786636880	13.9 Volt	380 Pkt	80 Pkt	52 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.079, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Effto: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)