APRS Track Direct

My position About ☰

reset

KB7DWO-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KB7DWO-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	DigiRpt*	RFiGate*	Temp*
1790638845	10 Pkts	38 Pkts	42 C
1790635245	9 Pkts	62 Pkts	42 C
1790631645	6 Pkts	30 Pkts	42 C
1790628045	11 Pkts	27 Pkts	41 C
1790624445	10 Pkts	50 Pkts	41 C
1790620845	23 Pkts	68 Pkts	41 C
1790617245	25 Pkts	56 Pkts	41 C
1790613645	29 Pkts	62 Pkts	41 C
1790610045	11 Pkts	35 Pkts	41 C
1790606445	11 Pkts	54 Pkts	41 C
1790602845	17 Pkts	51 Pkts	41 C
1790599245	8 Pkts	32 Pkts	41 C
1790595645	8 Pkts	42 Pkts	41 C
1790592045	9 Pkts	34 Pkts	41 C
1790588445	8 Pkts	31 Pkts	41 C
1790584845	8 Pkts	31 Pkts	41 C
1790581245	8 Pkts	27 Pkts	41 C
1790577645	9 Pkts	30 Pkts	41 C
1790574045	8 Pkts	30 Pkts	41 C
1790570445	6 Pkts	25 Pkts	41 C
1790566845	9 Pkts	33 Pkts	41 C
1790563245	7 Pkts	32 Pkts	42 C
1790559645	9 Pkts	30 Pkts	42 C
1790556045	8 Pkts	62 Pkts	42 C

*Used Equation Coefficients:

DigiRpt: 0, 1, 0

RFiGate: 0, 1, 0

Temp: 0, 1, 0

V1: 0, 0.1, 0

InetiGate: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)