APRS Track Direct

My position About ☰

reset

LD7TG Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LD7TG. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1786733687	13.8 Volt	470 Pkt	110 Pkt	74 Pcnt
1786730087	13.88 Volt	450 Pkt	110 Pkt	68 Pcnt
1786726487	13.8 Volt	580 Pkt	100 Pkt	66 Pcnt
1786722887	13.8 Volt	500 Pkt	90 Pkt	69 Pcnt
1786719287	13.88 Volt	600 Pkt	130 Pkt	66 Pcnt
1786715687	13.88 Volt	640 Pkt	150 Pkt	65 Pcnt
1786712088	13.8 Volt	680 Pkt	150 Pkt	65 Pcnt
1786708488	13.8 Volt	670 Pkt	130 Pkt	66 Pcnt
1786704888	13.8 Volt	750 Pkt	160 Pkt	67 Pcnt
1786701288	13.8 Volt	750 Pkt	150 Pkt	72 Pcnt
1786697688	13.88 Volt	700 Pkt	140 Pkt	73 Pcnt
1786694088	13.88 Volt	700 Pkt	160 Pkt	73 Pcnt
1786690488	13.8 Volt	720 Pkt	170 Pkt	73 Pcnt
1786686889	13.73 Volt	720 Pkt	150 Pkt	71 Pcnt
1786683289	13.8 Volt	620 Pkt	130 Pkt	70 Pcnt
1786679689	13.8 Volt	560 Pkt	80 Pkt	70 Pcnt
1786676089	13.88 Volt	540 Pkt	90 Pkt	67 Pcnt
1786672489	13.88 Volt	460 Pkt	90 Pkt	65 Pcnt
1786668889	13.8 Volt	440 Pkt	80 Pkt	64 Pcnt
1786665289	13.88 Volt	510 Pkt	70 Pkt	66 Pcnt
1786661690	13.88 Volt	490 Pkt	70 Pkt	65 Pcnt
1786658090	13.8 Volt	520 Pkt	80 Pkt	62 Pcnt
1786654490	13.8 Volt	560 Pkt	100 Pkt	67 Pcnt
1786650890	13.8 Volt	620 Pkt	120 Pkt	68 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)