APRS Track Direct

My position About ☰

reset

LU8DCH-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LU8DCH-2. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	RxTraffic*	RxDrop*	RSSI*	Voltage*
1770185202	51 Pkt	0 Pkt	31 dBm	12.43 V
1770181553	37 Pkt	0 Pkt	31 dBm	12.43 V
1770166971	29 Pkt	0 Pkt	31 dBm	12.43 V
1770163323	36 Pkt	0 Pkt	31 dBm	12.43 V
1770157855	19 Pkt	1 Pkt	31 dBm	12.43 V
1770154210	19 Pkt	1 Pkt	31 dBm	12.43 V
1770152388	17 Pkt	3 Pkt	31 dBm	12.43 V
1770150565	22 Pkt	5 Pkt	31 dBm	12.43 V
1770145098	19 Pkt	4 Pkt	31 dBm	12.43 V
1770143275	8 Pkt	7 Pkt	31 dBm	12.43 V
1770135984	18 Pkt	26 Pkt	31 dBm	12.43 V
1770128695	19 Pkt	2 Pkt	31 dBm	12.43 V
1770123227	18 Pkt	27 Pkt	31 dBm	12.43 V
1770117760	48 Pkt	5 Pkt	31 dBm	12.43 V
1770115937	41 Pkt	6 Pkt	31 dBm	12.43 V
1770110468	50 Pkt	36 Pkt	31 dBm	12.39 V
1770104998	39 Pkt	48 Pkt	31 dBm	12.43 V
1770103175	62 Pkt	39 Pkt	31 dBm	12.43 V
1770099529	50 Pkt	45 Pkt	31 dBm	12.43 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)