APRS Track Direct

My position About ☰

reset

N6LED-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object N6LED-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	RFIn*	RFiGate*	Temp*
1754145949	131 Pkts	131 Pkts	19 C
1754142348	108 Pkts	108 Pkts	19 C
1754138748	79 Pkts	79 Pkts	20 C
1754135149	95 Pkts	94 Pkts	19 C
1754131548	93 Pkts	92 Pkts	20 C
1754127949	88 Pkts	86 Pkts	20 C
1754124349	114 Pkts	114 Pkts	20 C
1754120749	117 Pkts	117 Pkts	20 C
1754117149	121 Pkts	120 Pkts	20 C
1754113549	119 Pkts	118 Pkts	20 C
1754109950	103 Pkts	103 Pkts	20 C
1754106349	75 Pkts	75 Pkts	20 C
1754102749	48 Pkts	48 Pkts	20 C
1754099149	86 Pkts	85 Pkts	21 C
1754095549	196 Pkts	193 Pkts	21 C
1754091957	164 Pkts	164 Pkts	21 C
1754088349	171 Pkts	170 Pkts	21 C
1754084749	180 Pkts	179 Pkts	20 C
1754081149	84 Pkts	84 Pkts	20 C
1754077549	62 Pkts	62 Pkts	20 C
1754073949	80 Pkts	79 Pkts	20 C
1754070349	109 Pkts	108 Pkts	20 C
1754066749	138 Pkts	137 Pkts	19 C
1754063149	166 Pkts	163 Pkts	19 C

*Used Equation Coefficients:

RFIn: 0, 1, 0

RFiGate: 0, 1, 0

DigiRpt: 0, 1, 0

Temp: 0, 1, 0

InetiGate: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)