APRS Track Direct

My position About ☰

reset

N5GAN-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object N5GAN-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	RFIn*	RFiGate*	DigiRpt*	Temp*
1836274546	88 Pkts	87 Pkts	18 Pkts	45 C
1762300741	46 Pkts	39 Pkts	16 Pkts	46 C
1762291313	41 Pkts	36 Pkts	17 Pkts	46 C
1762287669	31 Pkts	25 Pkts	3 Pkts	46 C
1762284076	39 Pkts	34 Pkts	7 Pkts	45 C
1762280469	28 Pkts	21 Pkts	9 Pkts	44 C
1762276865	53 Pkts	46 Pkts	13 Pkts	44 C
1762273265	63 Pkts	56 Pkts	12 Pkts	42 C
1762269666	100 Pkts	93 Pkts	26 Pkts	42 C
1762266065	65 Pkts	58 Pkts	13 Pkts	41 C
1762260512	28 Pkts	24 Pkts	4 Pkts	40 C
1762256912	42 Pkts	35 Pkts	12 Pkts	41 C
1762253312	65 Pkts	58 Pkts	16 Pkts	41 C
1762249712	59 Pkts	54 Pkts	16 Pkts	41 C
1762246112	56 Pkts	49 Pkts	17 Pkts	41 C
1762242512	26 Pkts	22 Pkts	10 Pkts	42 C
1762238914	32 Pkts	26 Pkts	6 Pkts	42 C
1762235312	30 Pkts	23 Pkts	8 Pkts	42 C
1762231712	13 Pkts	10 Pkts	3 Pkts	42 C

*Used Equation Coefficients:

RFIn: 0, 1, 0

RFiGate: 0, 1, 0

DigiRpt: 0, 1, 0

Temp: 0, 1, 0

InetiGate: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)