APRS Track Direct

My position About ☰

reset

9M4GDD Telemetry

This is the latest recevied telemetry packets stored in our database for station/object 9M4GDD. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	TxTraffic*	RSSI*	Voltage*
1782543031	40 Pkt	-53 dBm	18.99 V
1782539408	19 Pkt	-50 dBm	19.03 V
1782535786	41 Pkt	-51 dBm	19.03 V
1782532163	12 Pkt	-52 dBm	19.05 V
1782528540	24 Pkt	-51 dBm	19.01 V
1782524917	23 Pkt	-51 dBm	19.01 V
1782521295	31 Pkt	-50 dBm	19.01 V
1782517672	13 Pkt	-52 dBm	19.03 V
1782514049	3 Pkt	-51 dBm	19.03 V
1782510427	1 Pkt	-49 dBm	19.03 V
1782506805	13 Pkt	-52 dBm	19.01 V
1782503183	11 Pkt	-49 dBm	19.01 V
1782499561	1 Pkt	-51 dBm	19.01 V
1782495939	1 Pkt	-53 dBm	19.03 V
1782492317	1 Pkt	-53 dBm	19.01 V
1782488694	3 Pkt	-52 dBm	19.01 V
1782485072	8 Pkt	-54 dBm	19.01 V
1782481450	13 Pkt	-54 dBm	19.01 V
1782477828	5 Pkt	-54 dBm	18.99 V
1782474205	13 Pkt	-54 dBm	18.99 V
1782470583	0 Pkt	-54 dBm	18.97 V
1782470223	1 Pkt	-54 dBm	18.99 V
1782466601	2 Pkt	-56 dBm	18.99 V
1782462979	25 Pkt	-54 dBm	18.99 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)