APRS Track Direct

My position About ☰

reset

PY4WVZ-15 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object PY4WVZ-15. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	TxTraffic*	RSSI*	Voltage*
1752727300	0 Pkt	-64 dBm	0.04 V
1752725361	48 Pkt	-67 dBm	0.04 V
1752723485	2 Pkt	-68 dBm	0.02 V
1752721543	48 Pkt	-66 dBm	0.04 V
1752719666	0 Pkt	-64 dBm	0.04 V
1752717716	54 Pkt	-66 dBm	0.04 V
1752710653	6 Pkt	-59 dBm	0.04 V
1752709569	6 Pkt	-63 dBm	0.04 V
1752708621	107 Pkt	-66 dBm	0.04 V
1752705123	3 Pkt	-67 dBm	0.04 V
1752703077	94 Pkt	-66 dBm	0.04 V
1752701144	1 Pkt	-63 dBm	0.04 V
1752699142	128 Pkt	-65 dBm	0.04 V
1752697200	8 Pkt	-64 dBm	0.04 V
1752695010	91 Pkt	-64 dBm	0.04 V
1752693086	2 Pkt	-62 dBm	0.04 V
1752691073	33 Pkt	-64 dBm	0.04 V
1752689210	1 Pkt	-62 dBm	0.04 V
1752687186	125 Pkt	-67 dBm	0.04 V
1752685226	13 Pkt	-68 dBm	0.04 V
1752683091	122 Pkt	-64 dBm	0.04 V
1752681132	4 Pkt	-59 dBm	0.04 V
1752679087	8 Pkt	-55 dBm	0.04 V
1752678795	147 Pkt	-58 dBm	0.04 V
1752676808	5 Pkt	-60 dBm	0.04 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)