APRS Track Direct

My position About ☰

reset

HP3ICC-12 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HP3ICC-12. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	RxTraffic*	RSSI*	Voltage*
1732221696	4 Pkt	-22 dBm	9.43 V
1732220471	2 Pkt	-25 dBm	9.41 V
1732219247	6 Pkt	-25 dBm	9.41 V
1732218022	5 Pkt	-23 dBm	9.43 V
1732216797	9 Pkt	-20 dBm	9.43 V
1732215571	3 Pkt	-21 dBm	9.43 V
1732214346	2 Pkt	-22 dBm	9.43 V
1732213121	1 Pkt	-24 dBm	9.43 V
1732211897	9 Pkt	-24 dBm	9.43 V
1732210672	2 Pkt	-24 dBm	9.41 V
1732209447	5 Pkt	-22 dBm	9.43 V
1732208222	4 Pkt	-22 dBm	9.41 V
1732206997	2 Pkt	-21 dBm	9.43 V
1732205773	3 Pkt	-21 dBm	9.41 V
1732204547	3 Pkt	-22 dBm	9.41 V
1732203322	2 Pkt	-22 dBm	9.41 V
1732202098	2 Pkt	-23 dBm	9.43 V
1732200873	4 Pkt	-22 dBm	9.43 V
1732199648	3 Pkt	-21 dBm	9.41 V
1732198424	4 Pkt	-21 dBm	9.41 V
1732197199	4 Pkt	-21 dBm	9.41 V
1732195974	3 Pkt	-21 dBm	9.43 V
1732194749	3 Pkt	-21 dBm	9.41 V
1732193525	4 Pkt	-21 dBm	9.41 V
1732192300	4 Pkt	-19 dBm	9.43 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)