APRS Track Direct

My position About ☰

reset

HP1GRE-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HP1GRE-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	RxTraffic*	RSSI*	Voltage*
1732468661	36 Pkt	-14 dBm	13.84 V
1732467434	23 Pkt	-15 dBm	13.84 V
1732466208	35 Pkt	-15 dBm	13.86 V
1732464978	44 Pkt	-15 dBm	13.84 V
1732463750	38 Pkt	-15 dBm	13.84 V
1732462522	23 Pkt	-15 dBm	13.84 V
1732461296	19 Pkt	-17 dBm	13.84 V
1732460070	22 Pkt	-14 dBm	13.84 V
1732458845	23 Pkt	-14 dBm	13.84 V
1732457619	19 Pkt	-14 dBm	13.84 V
1732456392	19 Pkt	-15 dBm	13.84 V
1732455167	20 Pkt	-16 dBm	13.84 V
1732453939	15 Pkt	-15 dBm	13.86 V
1732452713	4 Pkt	-15 dBm	13.84 V
1732451425	23 Pkt	-13 dBm	13.84 V
1732450199	23 Pkt	-13 dBm	13.84 V
1732448973	25 Pkt	-12 dBm	13.84 V
1732447745	29 Pkt	-12 dBm	13.84 V
1732446517	25 Pkt	-12 dBm	13.84 V
1732445291	29 Pkt	-13 dBm	13.84 V
1732444064	26 Pkt	-13 dBm	13.84 V
1732442836	26 Pkt	-13 dBm	13.86 V
1732441609	26 Pkt	-12 dBm	13.84 V
1732440382	30 Pkt	-12 dBm	13.84 V
1732439156	26 Pkt	-13 dBm	13.86 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)