APRS Track Direct

My position About ☰

reset

WA4TAL-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object WA4TAL-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	RFIn*	RFiGate*	Temp*
1750199605	389 Pkts	358 Pkts	35 C
1750196004	329 Pkts	296 Pkts	35 C
1750192404	274 Pkts	250 Pkts	35 C
1750188805	254 Pkts	229 Pkts	35 C
1750185205	228 Pkts	210 Pkts	35 C
1750181603	245 Pkts	218 Pkts	35 C
1750178007	260 Pkts	235 Pkts	35 C
1750174405	367 Pkts	345 Pkts	36 C
1750170804	471 Pkts	448 Pkts	35 C
1750167203	476 Pkts	452 Pkts	35 C
1750163605	410 Pkts	396 Pkts	35 C
1750160004	405 Pkts	390 Pkts	35 C
1750156405	488 Pkts	466 Pkts	35 C
1750152804	467 Pkts	447 Pkts	35 C
1750149203	463 Pkts	441 Pkts	35 C
1750145604	425 Pkts	398 Pkts	35 C
1750142003	430 Pkts	403 Pkts	35 C
1750138403	388 Pkts	363 Pkts	35 C
1750134804	458 Pkts	430 Pkts	35 C
1750131204	414 Pkts	393 Pkts	35 C
1750127604	427 Pkts	403 Pkts	35 C
1750124004	290 Pkts	262 Pkts	35 C
1750120404	248 Pkts	226 Pkts	35 C
1750116803	476 Pkts	451 Pkts	35 C

*Used Equation Coefficients:

RFIn: 0, 1, 0

RFiGate: 0, 1, 0

DigiRpt: 0, 1, 0

Temp: 0, 1, 0

InetiGate: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)