APRS Track Direct

My position About ☰

reset

HS4ADH-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HS4ADH-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	TxTraffic*	RSSI*	Voltage*
1750106216	0 Pkt	-58 dBm	0.12 V
1750104406	0 Pkt	-58 dBm	0.12 V
1750102596	0 Pkt	-59 dBm	0.1 V
1750100786	0 Pkt	-59 dBm	0.08 V
1750098976	0 Pkt	-57 dBm	0.06 V
1750097167	0 Pkt	-59 dBm	0 V
1750095356	0 Pkt	-59 dBm	0.08 V
1750093546	0 Pkt	-58 dBm	0.08 V
1750091736	1 Pkt	-58 dBm	0.08 V
1750089926	0 Pkt	-59 dBm	0.08 V
1750088042	5 Pkt	-58 dBm	0.12 V
1750086232	0 Pkt	-58 dBm	0.06 V
1750084422	0 Pkt	-60 dBm	0.1 V
1750082612	0 Pkt	-60 dBm	0.1 V
1750080802	0 Pkt	-59 dBm	0.06 V
1750078992	2 Pkt	-58 dBm	0.02 V
1750077182	12 Pkt	-62 dBm	0.04 V
1750075372	0 Pkt	-62 dBm	0.12 V
1750073562	0 Pkt	-57 dBm	0.08 V
1750071752	0 Pkt	-61 dBm	0.06 V
1750069867	0 Pkt	-61 dBm	0.08 V
1750068057	1 Pkt	-63 dBm	0.04 V
1750066247	1 Pkt	-62 dBm	0.04 V
1750064437	1 Pkt	-60 dBm	0.06 V
1750062627	0 Pkt	-59 dBm	0.04 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)