APRS Track Direct

My position About ☰

reset

TA4TX Telemetry

This is the latest recevied telemetry packets stored in our database for station/object TA4TX. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	RxTraffic*	RSSI*	Voltage*
1790666731	6 Pkt	-63 dBm	11.53 V
1790664909	4 Pkt	-64 dBm	11.53 V
1790663087	5 Pkt	-62 dBm	11.53 V
1790661265	5 Pkt	-64 dBm	11.53 V
1790659443	8 Pkt	-62 dBm	11.53 V
1790657619	6 Pkt	-60 dBm	11.53 V
1790655797	6 Pkt	-64 dBm	11.53 V
1790653975	5 Pkt	-63 dBm	11.53 V
1790652153	5 Pkt	-63 dBm	11.53 V
1790650331	5 Pkt	-62 dBm	11.53 V
1790648508	8 Pkt	-61 dBm	11.53 V
1790646686	5 Pkt	-61 dBm	11.53 V
1790644864	6 Pkt	-60 dBm	11.53 V
1790643042	3 Pkt	-61 dBm	11.53 V
1790641220	8 Pkt	-61 dBm	11.53 V
1790639397	3 Pkt	-61 dBm	11.53 V
1790637575	6 Pkt	-60 dBm	11.53 V
1790635753	7 Pkt	-61 dBm	11.53 V
1790633931	4 Pkt	-64 dBm	11.53 V
1790632108	3 Pkt	-62 dBm	11.53 V
1790630286	8 Pkt	-64 dBm	11.53 V
1790628464	4 Pkt	-61 dBm	11.53 V
1790626642	5 Pkt	-62 dBm	11.53 V
1790624819	8 Pkt	-62 dBm	11.53 V
1790622997	5 Pkt	-61 dBm	11.53 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)