APRS Track Direct

My position About ☰

reset

HP3ICC-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HP3ICC-2. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	RxTraffic*	RSSI*	Voltage*
1836274547	13 Pkt	-10 dBm	5.17 V
1770219705	6 Pkt	-11 dBm	5.21 V
1770217880	6 Pkt	-9 dBm	5.19 V
1770216054	4 Pkt	-10 dBm	5.19 V
1770214229	2 Pkt	-8 dBm	5.25 V
1770212404	0 Pkt	-11 dBm	5.19 V
1770210579	0 Pkt	-12 dBm	5.21 V
1770208754	0 Pkt	-15 dBm	5.19 V
1770206929	0 Pkt	-13 dBm	5.19 V
1770205104	0 Pkt	-8 dBm	5.13 V
1770203279	0 Pkt	-8 dBm	5.17 V
1770201454	0 Pkt	-8 dBm	5.17 V
1770199629	0 Pkt	-9 dBm	5.17 V
1770197803	0 Pkt	-14 dBm	5.19 V
1770195978	0 Pkt	-7 dBm	5.21 V
1770194153	0 Pkt	-9 dBm	5.21 V
1770192328	0 Pkt	-9 dBm	5.19 V
1770190503	0 Pkt	-14 dBm	5.17 V
1770188678	0 Pkt	-12 dBm	5.17 V
1770186852	0 Pkt	-9 dBm	5.19 V
1770185027	0 Pkt	-9 dBm	5.19 V
1770182920	0 Pkt	-8 dBm	5.19 V
1770181094	1 Pkt	-12 dBm	5.19 V
1770179269	1 Pkt	-9 dBm	5.17 V
1770177444	4 Pkt	-9 dBm	5.21 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)