APRS Track Direct

My position About ☰

reset

DB0IS Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DB0IS. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	BATT*	CPU*	CASE*	OUT*	PA*
1786730897	24.2 V	61.2 C	29.5 C	22.1 C	0 W
1786730296	24.2 V	61.2 C	29.5 C	22.1 C	0 W
1786729696	24.2 V	61.2 C	30 C	22.1 C	0 W
1786729095	24.2 V	61.2 C	29.5 C	22.1 C	0 W
1786728495	24.2 V	61.2 C	29.5 C	22.1 C	0 W
1786727894	24.1 V	61.2 C	30 C	22.1 C	0 W
1786727294	24.2 V	61.7 C	29.5 C	22.1 C	0 W
1786726694	24.2 V	61.7 C	30 C	22.1 C	0 W
1786726094	24.1 V	61.2 C	29.5 C	22.1 C	0 W
1786725493	24.1 V	61.7 C	29.5 C	22.1 C	0 W
1786724893	24.2 V	61.2 C	29.5 C	22.1 C	0 W
1786724293	24.2 V	61.7 C	30 C	22.1 C	0 W
1786723693	24.2 V	61.7 C	30.5 C	22.1 C	0 W
1786723093	24.2 V	61.7 C	30 C	22.1 C	0 W
1786722492	24.2 V	61.2 C	29.5 C	22 C	0 W
1786721892	24.2 V	61.2 C	29.5 C	22 C	0 W
1786721291	24.2 V	61.7 C	30 C	22 C	0 W
1786720694	24.1 V	61.2 C	29.5 C	22 C	0 W
1786720091	24.2 V	61.7 C	30 C	22 C	0 W
1786719491	24.2 V	61.7 C	31.5 C	22 C	0 W
1786718890	23.8 V	61.2 C	29.5 C	22 C	4.7 W
1786718290	24.2 V	61.2 C	29.5 C	22 C	0 W
1786717689	24.1 V	61.2 C	29.5 C	21.9 C	0 W
1786717089	24.2 V	61.2 C	29.5 C	21.9 C	0 W
1786716489	24.1 V	61.7 C	30 C	21.8 C	0 W

*Used Equation Coefficients:

BATT: 0, 0.1, 0

CPU: 0, 0.1, 0

CASE: 0, 0.1, 0

OUT: 0, 0.1, 0

PA: 0, 0.1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)