APRS Track Direct

My position About ☰

reset

VE3XII-12 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VE3XII-12. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Vin*	Rx1h*	Eff1h*
1758200471	12.3 Volt	800 Pkt	770 Pcnt
1758199211	12.3 Volt	770 Pkt	760 Pcnt
1758197951	12.3 Volt	740 Pkt	760 Pcnt
1758196691	12.3 Volt	710 Pkt	770 Pcnt
1758195431	12.3 Volt	660 Pkt	780 Pcnt
1758194171	12.3 Volt	670 Pkt	800 Pcnt
1758192911	12.3 Volt	660 Pkt	810 Pcnt
1758191651	12.3 Volt	700 Pkt	770 Pcnt
1758190391	12.3 Volt	670 Pkt	750 Pcnt
1758189131	12.3 Volt	590 Pkt	700 Pcnt
1758187871	12.3 Volt	510 Pkt	650 Pcnt
1758186612	12.3 Volt	510 Pkt	640 Pcnt
1758185352	12.3 Volt	520 Pkt	660 Pcnt
1758184092	12.3 Volt	540 Pkt	660 Pcnt
1758182832	12.3 Volt	490 Pkt	630 Pcnt
1758181572	12.3 Volt	470 Pkt	590 Pcnt
1758180312	12.3 Volt	430 Pkt	570 Pcnt
1758179052	12.3 Volt	400 Pkt	560 Pcnt
1758177792	12.3 Volt	420 Pkt	580 Pcnt
1758176532	12.3 Volt	430 Pkt	580 Pcnt
1758175272	12.3 Volt	420 Pkt	550 Pcnt
1758174012	12.3 Volt	330 Pkt	510 Pcnt
1758172752	12.3 Volt	250 Pkt	460 Pcnt
1758171492	12.3 Volt	240 Pkt	480 Pcnt
1758170233	12.3 Volt	330 Pkt	590 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Rx10m: 0, 10, 0

Eff1h: 0, 10, 0

EffTo: 0, 10, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)